Bearing Pullers

A bearing puller is a tool specifically designed to remove or install bearings from rotating machine shafts or from blind bearing holes. Dependant on the size of the puller, the application can vary dramatically, ranging from transmission to complicated industry machinery.

Where can a Bearing Puller be used?

One of the main uses of a bearing puller in within a car, removing a caged set of ball and tapered bearings from a rotary shaft. Different types of bearing pullers will depend on the application they are used for:

Hydraulic pullers are designed to pull any bearing, belt pulley, gear, round wheel or other tightened part used within the machinery industry. One of the main features of using a hydraulic version is that the job of removing or dismounting a bearing is much simpler, faster and safer.

Strong back pullers are used for easy insertion between bearing and shoulders on a shaft, featuring a spring operated centre point and a safety valve, minimising puller overload.

Heavy-duty jaw pullers are considered the most versatile, they offer easy and effective dismount of bearings. They offer minimal damage to a bearing, through the use of a jaw, the whole operation is of pulling a bearing is easy and safe. Jaws are commonly used in industrial and commercial environments.

Internal bearing pullers can be used for removing grooved ball bearings efficiently from shafts and cases without dismounting a bearing. This is known as a user friendly option because some gear puller sets feature an elastic retaining ring which helps keep the puller arm in position.

How Bearing Pullers work

Usually a hand powered tool or tool kit that features a handle on the turn screw, or a male hex end to match a drive socket. There are mechanical pullet sets, hydraulic puller sets, gear puller sets and standard bearing pullers available that mimic the same actions of the hand powered gear puller.

Features of a Puller Kit
  • Pullers are often made from tool grade steel, which means that they are harder than the materials that they are being used on. This ensures that they do not break when they are pulling bearings.
  • Reversible for internal or external uses
  • Two or three claw design
  • Spring loaded centre point

...
Read more Read less

Filters

Viewing 81 - 83 of 83 products
Results per page
Description Price Capacity Hydraulic Force Operation Number of Pieces Case Material
RS Stock No. 124-8452
Mfr. Part No.TMMR200F
BrandSKF
SGD238.51
Each
units
204 mm - Hand - -
RS Stock No. 124-8448
Mfr. Part No.TMMR120F
BrandSKF
SGD164.90
Each
units
124 (External) mm, 139 (Internal) mm - Hand - -
RS Stock No. 300-6275
Mfr. Part No.U.35P
BrandFacom
SGD206.80
Each
units
55 mm - Gear - -
Related Products
The SKF TMBS E series of back pullers ...
Description:
The SKF TMBS E series of back pullers are easily inserted between the bearing and shoulder on the shaft. They have a spring loaded centre point allowing easier puller centring and a safety valve minimising puller overload. • TMBS 100E ...
The TMHS 100 hydraulic spindle from SKF generates ...
Description:
The TMHS 100 hydraulic spindle from SKF generates a high pulling force with only a small amount of effort. Unlike standard mechanical spindles, they can dismount bearings in in a reduced time. The cylinder, pump and spindle are fully integrated ...
The TMSC series of internal bearing pullers provide ...
Description:
The TMSC series of internal bearing pullers provide a positive grip of the bearing by expanding the collet adapters on the rear side of the bearing bore. The adapters are connected to a slide hammer which generates enough impact to ...
4" 50-100mm spread6" 75-150mm spread8" 75-150mm spread10" 150-250mm ...
Description:
4" 50-100mm spread6" 75-150mm spread8" 75-150mm spread10" 150-250mm spread. 10 Ton hydraulic power easily pulls hubs, flanges, gears and bearings2//3 way cross-head and 3x3 position puller armsMaximum reach 160mmTypical pulling tasks:.