United Automation, PFC2 100KVR, Power Factor Switch, 150A, 5.6kg, 270 x 250 x 130mm

Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

PFC2 80/100kVAR Power Factor Switches

The PFC2 controllers are suitable for 3-wire, 3-phase floating-star or closed-delta configured capacitive loads for Power Factor Correction and can be used in capacitor banks with or without chokes fitted. They are designed to dramatically reduce the inrush current normally found with contactor-based systems and could be used in situations where rapid changes in Power Factor occur such as welding plants, lifts, cranes and wind-powered plants.

Current rating: 125A (80kVAR), 150A (100kVAR) @ 415Vrms
Input voltage: 415Vrms ±10%
Frequency: 50/60Hz
Control signal input: +8 to +24Vdc, Common 0V or Common +VE, Open Collector or Volt Free Contact
Alarm relay functions: Voltage free alarm relay is rated for 125Vac @ 2A.
LED indicators: Green = DC Power ON, Red = Fault, Orange = Signal enabled, Red/Orange = Capacitors discharging
Cooling fan: +24Vdc
Fan ’switch-on’: Typically +55ºC
Over Temperature: Trip in temperature: +90ºC ±1ºC (Status LED indicator ’flashes’ with ON/OFF rapid pulsing
Trip out temperature: +85ºC ±1ºC
Phase loss detection: Phase loss or Fuse failure orange and red LEDs flash alternately
Status LED Fault condition: Status LED indicator ’flashes’ ON/OFF continuously at 1.5 second intervals
Sensor loss detection: Status LED indicator ’flashes’ ON/OFF continuously in equal intervals
Power cable terminations: Supply, Load & Earth 35mm² rising clamp terminal block
Terminal torque settings: 3.2Nm min (35mm²) Power terminals only
Signal cable terminations: Remote supply Auxiliary alarm (relay) 2.5mm² rising clamp terminal block
Control signal 2.5mm² rising clamp terminal block
Environmental Protection: IP20
Fusing 80kVAR: 160EET (160A) High-Speed Semiconductor type fuse, or equivalent
Fusing 100kVAR: 200EET (200A) High-Speed Semiconductor type fuse, or equivalent
Working temperature: +65°C (maximum operational)
Dimensions: 270 x 250 x 130mm
Fixing centres: 4 x 4.5mm-clear keyhole slots on fixing centres 227 x 200mm
Weight: 5.6kg

RS Product Codes
919-6232 PFC2 80kVAR
919-6236 PFC2 100kVAR

Warning

  • Metal parts, in particular the case may get very hot when the unit is fully operational.
Specifications
Attribute Value
Current Rating 150A
Weight 5.6kg
Mounting Type Panel Mount
Dimensions 270 x 250 x 130mm
Fixing Centres 227 x 200mm
Length 270mm
Width 250mm
Height 130mm
Maximum Operating Temperature +65 °C
Temporarily out of stock - back order for despatch 13/03/2020, delivery within 3 working days from despatch date
Price Each
SGD 1,213.35
(exc. GST)
SGD 1,298.28
(inc. GST)
units
Per unit
1 - 4
SGD1,213.35
5 - 9
SGD1,126.68
10 +
SGD1,056.26
Related Products
High-frequency clock and data signal multiplexer (MUX) devices ...
Description:
High-frequency clock and data signal multiplexer (MUX) devices capable of operating at speeds of up to 10 GHz with extremely fast rise and fall times. Various input and output configurations and logic-level standards are available, including CML, ECL, PECL, LVPECL ...
2.5KW compact (module only)Integral heat sink for maximum ...
Description:
2.5KW compact (module only)Integral heat sink for maximum power capabilitySingle Phase 230/240Vac Input Voltage0 to 10Vdc Control InputSolid State ControlLED power level indicationOver Temperature Protection with auto shutdown and resetSimple DIN Rail or panel mountingSuitable for ceiling or radiant heating, ...
Compact unit for proportional linear control of resistive ...
Description:
Compact unit for proportional linear control of resistive loads using variable on/off bursts of complete main cycles, coincident with mains zero crossoverCan be used with most resistive heater loadsLarge triac handles high inrush currentIntegral heat sink provides high temp reliability. ...
The PRx-E thyristor stack units provide full seamless ...
Description:
The PRx-E thyristor stack units provide full seamless control of 1/3-phase resistive loads. Burst-firing control stack uses fast pulse zero-voltage switching technology to minimise flicker and RFI problemsIntegral fusing, temperature trip, automatic reset and heatsinkHoused in bespoke enclosures with easy ...