Honeywell Vibration Sensor -55°C → +120°C, Dimensions 19.05 (Dia.) x 56.88 mm

  • RS Stock No. 822-8398
  • Mfr. Part No. 3030AN
  • Manufacturer Honeywell
Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
COO (Country of Origin): MX
Product Details

Honeywell VRS Sensors

Honeywell offers VRS sensors for high output, general purpose, power output, high resolution, high temperature, and hazardous location applications. High Output VRS sensors are designed for use in applications where higher output voltages are needed. For best performance use in applications of low to medium speeds with medium to high impedance loads. General Purpose VRS sensors are designed for use in applications with medium to high speeds or in electrically noisy environments with relatively small air gaps. Passive Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions. VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation.

The fixed magnetic field is established by use of a permanent magnet. As a ferrous metal object approaches and passes near the sensing area the flux lines of the magnetic field change in strength. This change in magnetic field strength induces a current into a coil winding, which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage. One complete waveform occurs as each target passes the sensor’s pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if viewed on an oscilloscope.

Self-powered operation
Direct conversion of actuator speed to output frequency
Simple installation
No moving parts
Designed for use over a wide range of speeds
Adaptable to a wide variety of configurations
Customized VRS products for unique speed sensing applications

Potential Applications:
Engine RPM measurement
Motor RPM measurement
Process speed measurement
Speed measurement of pumps, blowers, mixers, exhaust and ventilating fans
Flow measurement on turbine meters
Wheel-slip measurement on autos and locomotives
Gear speed measurement

Attribute Value
Minimum Operating Temperature -55°C
Maximum Operating Temperature +120°C
Switching Frequency 15 kHz
11 In stock for delivery within 3 working days
Price Each
SGD 124.48
(exc. GST)
SGD 133.19
(inc. GST)
Per unit
1 - 9
10 - 24
25 - 49
50 - 99
100 +
Related Products
All dc switches in this range have reverse ...
All dc switches in this range have reverse polarity and short circuit protection. Embeddable versions can be flush mounted in metal. Polyamide housingIP67Operating temperature range –25 to +70°CShort circuit and reverse polarity protectionDimensions LxWxH (mm): 16x8x4.7Pre-wired with 0.23m of cable. ...
Working temperature from -50 °C → +600 °CFlexible, ...
Working temperature from -50 °C → +600 °CFlexible, thin-walled sheathed wire made of stainless steel; the low-ohm copper internal conducting wires are embedded in compressed, fire-resistant magnesium oxide for vibration resistanceTwo or three-conductor circuitRapid response timesConnection lead made of silicon, ...
Platinum chip temperature sensors Pt100, Pt500 and Pt1000. ...
Platinum chip temperature sensors Pt100, Pt500 and Pt1000. For temperatures between -70 °C and +600 °CNominal value of 100 Ω / 500 Ω / 1000 ΩStandardised nominal values and tolerancesSmall dimensionsRapid response timeImpervious to shocks and vibrations.
Twin-element Duplex detector utilising two pure platinum wires ...
Twin-element Duplex detector utilising two pure platinum wires wound into a miniature spiral and located within axial holes in a high purity alumina rod. The high stability Duplex sensor can be connected to the measuring or control device with two ...