Ferrite Beads

"

Ferrite Beads also known as ferrite chokes are passive devices and they are used to constrict high-frequency signals in electronic components. The ferrite becomes resistive over its intended frequency range and uses up the noise energy in the form of heat.


How do the ferrite beads work?


The ferrite bead is connected in series with the power supply rail and is often combined with the capacitors to ground on either side of the bead. This then forms a low-pass filter network, further reducing the high-frequency power supply noise. Use SPICE (Simulation Program with Integrated Circuit Emphasis) or another similar tool to ensure any anti-resonance peaks caused by ferrite or PCB inductive structure does not violate the target impedance limit.


Ferrite Beads come in two categories:


High-Q Beads - typically used as resonators and must not be used in power isolation circuits


Low-Q Beads - these are also called absorptive beads and they are lossy and make good filter networks because they are designed to absorb high-frequency noise currents and dissipate it as heat


What to consider when choosing Ferrite Beads?


Make sure that any voltage drop does not cause the target supply rail to fall below the recommended operating conditions of the device


The ferrite bead is inductive, therefore do not use it with High-Q decoupling capacitors


Applying ferrite beads correctly can be an effective and inexpensive way to reduce high-frequency noise and switching transients


Where are Ferrite Beads used?


Eliminating high-frequency EMI noise on any circuit design


Electronic devices such as mobile phones


Computers and laptops


TV tuners


Audio Players


DVD’s


Gaming Systems

"

...
Read more Read less

Filters

Viewing 1241 - 1242 of 1242 products
Results per page
Description Price Package Type Impedance at 25 MHz Impedance at 100 MHz Impedance at 300 MHz Impedance at 500 MHz Impedance at 1 GHz Current Rating Type Dimensions Length Depth Height Diameter Application
RS Stock No. 792-6274
Mfr. Part No.BLM18PG121SH1D
BrandMurata
SGD0.107
Each (In a Bag of 25)
units
0603 (1608M) - 120Ω - - - 2A Chip Ferrite Bead 1.6 x 0.8 x 0.8mm 1.6mm 0.8mm 0.8mm - EMI Suppression Filter, Power Supplies
RS Stock No. 888-3055
Mfr. Part No.HI1806T600R-10
SGD0.134
Each (In a Pack of 500)
units
1806 (4516M) 28Ω 60Ω - - 92Ω 6A Chip Bead 4.5 x 1.6 x 1.6mm 4.5mm 1.6mm 1.6mm - Automotive, DSC, Energy and Utilities, General Electronics, Laptop, LCD-TV, Networking Devices, PC, Portable Devices etc., Security
Related Products
BLM ferrite beads from Murata are ideal for ...
Description:
BLM ferrite beads from Murata are ideal for use in circuits with unstable ground lines as they do not require a ground connection. At noise frequencies, these ferrite beads are designed to function nearly as a resistor, leaving signal wave ...
The BMB B Series of beads cover a ...
Description:
The BMB B Series of beads cover a wide range of impedance and frequency characteristics. This series is suited to various applications. BMB-B Series minimise the attenuation of the signal wave form due to its sharp impedance characteristics thus effective ...
Excellent anti-EMI properties and low DC resistancePlaced very ...
Description:
Excellent anti-EMI properties and low DC resistancePlaced very close next to the interference source even with smallest size 0402, maximum impedance 1000ΩReliable Ni-Sn electrodes Ideal for data line filtering and voltage de-couplingHigh rated current up to 6A Recommended for reflow ...
This is a multilayered chip bead product which ...
Description:
This is a multilayered chip bead product which is magnetically shielded, allowing high density mountingReduced floating capacity between conductors has contributed to a dramatic improvement in high frequency characteristicsThe EMI suppression provided extends into the GHz rangeApplication include removal of ...